We use cookies to run this site. With your permission we also use analytics cookies to understand site traffic. Analytics stays off until you allow it. Privacy
WARNING: Cancer and Reproductive Harm - www.p65warnings.ca.gov
1" Heavy Wall Heat Shrink
Adhesive Lined
Crosslinked Polyolefin Heat Shrink
Red
Cut piece 1 1/2" Length
Impact, abrasion, corrosion, and chemical resistant; suitable for submersion and direct burial
Features:
Applications:
-55°C to 110°C
Select a size which will shrink snugly over the component to be covered. Match your component diameter with the Recovered Inside Diameter (d) for the best fit. Restricted recovery will result in lower wall thickness.
HSREDHD-1
D: 1.1 in. (27.9mm)
d: 0.35 in. (8.9mm)
w: 0.12 in. (3mm)
| Physical Property | Test Method | Typical Performance |
|---|---|---|
| Tensile Strength | ASTM D412, ISO 37 |
2100 psi (14.5 MPa) |
| Elongation | ASTM D412, ISO 37 |
600% |
| Elongation after heat aging (168 hours at 175°C) |
ASTM D2671, ISO 37 |
500% (250%) |
| Longitudinal change on recovery |
ASTM D2671 | +1%, -10% |
| Specific Gravity | ASTM D792 | 1.1 |
| Heat shock (4 hours at 255°C) |
ASTM D2671 | No cracking or flowing |
| Low temperature flexibility (4 hours at -55°C) |
ASTM D2671 | No cracking or splitting |
| Hardness (Shore D) | ASTM D2240 | 50D |
| Oxygen Index | ASTM D2863 | 27.00 |
| Flammability | ASTM D2671 | Flame Retardant |
| Electrical Property | ||
| Dielectric Strength | ASTM D149 | 500 V/Mil (20kV/mm) |
| Dielectric Voltage Withstand (2500V, 60Hz, 1 min.) |
UL 486D | No breakdown, 24kV-1 Min. 15kV-4 hrs. |
| Volume Resistivity | ASTM D257 | 1016 ohm-cm |
| Chemical Property | ||
| Fluid Resistance | MIL-DTL- 23053/15 |
Good to excellent |
| Copper Corrosion | ASTM D2671 | No Corrosion |
| Water Absorption | ASTM D570 | 0.2% |
| Fungus Resistance | ASTM G21 | No growth |
| Adhesive Property | ||
| Adhesive softening point | ASTM E28 | 92°C +/- 5°C |
| Adhesive peel strength (300mm/min at 23°C) - to steel, aluminum, P.E. - to PVC |
ASTM D1000 ASTM D1000 |
35 pli 20 pli |
| Adhesive lap shear (1in./min at 23°C) |
ASTM D1002 | 125 psi (0.875 MPa) |
| Adhesive Blocking (30°C) | ASTM D1146 | No blocking |
| Adhesive water absorption | ASTM D570 | less than 0.3% |
| Water penetration | STM 706 | No penetration after 236 hrs of continuous immersion |
ArrivesTue, Aug 18 - Wed, Aug 19
ArrivesTue, Aug 18 - Wed, Aug 19
ArrivesTue, Aug 18 - Wed, Aug 19
ArrivesTue, Aug 18 - Wed, Aug 19
ArrivesTue, Aug 18 - Wed, Aug 19
HSREDHD-1
EACH
Precut
Heavy Wall
Red
1"
0.01 lb
Item Number: HSREDHD-1
Tue, Aug 18 - Wed, Aug 19
Order within 1h 7m
Item Number: HSREDHD-1
WARNING: Cancer and Reproductive Harm - www.p65warnings.ca.gov
Tue, Aug 18 - Wed, Aug 19
Order within 1h 7m
HSREDHD-1
EACH
Precut
Heavy Wall
Red
1"
0.01 lb
1" Heavy Wall Heat Shrink
Adhesive Lined
Crosslinked Polyolefin Heat Shrink
Red
Cut piece 1 1/2" Length
Impact, abrasion, corrosion, and chemical resistant; suitable for submersion and direct burial
Features:
Applications:
-55°C to 110°C
Select a size which will shrink snugly over the component to be covered. Match your component diameter with the Recovered Inside Diameter (d) for the best fit. Restricted recovery will result in lower wall thickness.
HSREDHD-1
D: 1.1 in. (27.9mm)
d: 0.35 in. (8.9mm)
w: 0.12 in. (3mm)
| Physical Property | Test Method | Typical Performance |
|---|---|---|
| Tensile Strength | ASTM D412, ISO 37 |
2100 psi (14.5 MPa) |
| Elongation | ASTM D412, ISO 37 |
600% |
| Elongation after heat aging (168 hours at 175°C) |
ASTM D2671, ISO 37 |
500% (250%) |
| Longitudinal change on recovery |
ASTM D2671 | +1%, -10% |
| Specific Gravity | ASTM D792 | 1.1 |
| Heat shock (4 hours at 255°C) |
ASTM D2671 | No cracking or flowing |
| Low temperature flexibility (4 hours at -55°C) |
ASTM D2671 | No cracking or splitting |
| Hardness (Shore D) | ASTM D2240 | 50D |
| Oxygen Index | ASTM D2863 | 27.00 |
| Flammability | ASTM D2671 | Flame Retardant |
| Electrical Property | ||
| Dielectric Strength | ASTM D149 | 500 V/Mil (20kV/mm) |
| Dielectric Voltage Withstand (2500V, 60Hz, 1 min.) |
UL 486D | No breakdown, 24kV-1 Min. 15kV-4 hrs. |
| Volume Resistivity | ASTM D257 | 1016 ohm-cm |
| Chemical Property | ||
| Fluid Resistance | MIL-DTL- 23053/15 |
Good to excellent |
| Copper Corrosion | ASTM D2671 | No Corrosion |
| Water Absorption | ASTM D570 | 0.2% |
| Fungus Resistance | ASTM G21 | No growth |
| Adhesive Property | ||
| Adhesive softening point | ASTM E28 | 92°C +/- 5°C |
| Adhesive peel strength (300mm/min at 23°C) - to steel, aluminum, P.E. - to PVC |
ASTM D1000 ASTM D1000 |
35 pli 20 pli |
| Adhesive lap shear (1in./min at 23°C) |
ASTM D1002 | 125 psi (0.875 MPa) |
| Adhesive Blocking (30°C) | ASTM D1146 | No blocking |
| Adhesive water absorption | ASTM D570 | less than 0.3% |
| Water penetration | STM 706 | No penetration after 236 hrs of continuous immersion |